The network cable in the weak current box has no label and the power supply cannot be plugged in. I cleaned it up and haven’t touched it for two years.
Two years ago, the broadband at home had a problem. I opened the weak current box and tried to unplug the optical modem and restart it. But I was confused by a bunch of cables: more than a dozen network cables were twisted and twisted. I couldn't tell which one led to the living room and which one led to the study. I couldn't even touch the power supply of the optical modem when I reached in. As a result, I pulled out the wrong one, and the TV screen went black. I spent the whole afternoon trying to get it back one by one. That weekend I rummaged through the entire box, labeling it, rearranging the equipment, and arranging and fixing the cables. From then on, the box door opened clean and I never missed pulling it out again.
The weak current boxes are in a mess. To put it bluntly, it's not because there are too many wires, but because no one has registered them. The idea of organizing is three steps: first identify the cables, then place the equipment, and finally organize and fix the cables. The only tools required are a roll of label paper (textured paper is also acceptable), a marker, and a pair of zip ties, which cost less than ten yuan. A line measuring instrument is not necessary, but having one that costs about fifteen dollars can avoid detours, as I mentioned before in the article about pressing the crystal head.
Do one thing first before taking action: take pictures, don’t even miss a single one
The biggest fear of tidying up is not the mess, but not being able to put it back together after dismantling it. Before moving any wires, use your mobile phone to take pictures of the inside and outside of the box: a panoramic picture, a picture of each device's interface, and pictures of which hole the power strip is plugged into. Don't trust your brain, trust your photos. My neighbor just didn't take any pictures, and after arranging the cables, the IPTV still couldn't show the picture. I went back and forth until midnight and found out that the network cable was plugged into the wrong port.
After taking the photo, start identifying the lines. There are three common types of wires in weak current boxes at home: network cables, coaxial cables (thick round wires from the cable TV generation), and fiber optic cables. The coaxial cable is probably useless now, don’t throw it away, coil it up and put a “spare” label on it and plug it into the corner of the box; fiber optic cable is the lifeblood of the operator, don’t break it or press it - I wrote an article about how delicate it is about light attenuation, the bending radius is less than 5 cm, the optical power drops directly downwards, this is often the root of the problem of fast and slow Internet speed at home (see Light failure troubleshooting article ).
There is no shortcut to identifying network cables, just try them one by one. Before you start, take a look at the switch: which port's light is flashing, which one is the live wire in use, and you can screen out a batch at a time; unplug one, go to each room to see which panel has no network, label it, plug it back in, and move on to the next one. It only takes two people to work together for half an hour, or just one person can start a video call with his mobile phone. If it's too troublesome, you can buy a line finder, which costs dozens of dollars. The transmitter is clipped on the line, and the receiver can be paired by scanning the panel one by one. I identified the thirteen wires that time and found that three of them were dead wires left during renovation. No equipment was connected to either end. I coiled them and marked them as "empty wires" and collected them directly.
How to place the equipment: put the optical modem in a low place, don’t stack the arhat
Most people's logic for arranging equipment is "how to fit it in": the optical modem is stacked on the router, and the switch is pressed on the power strip. There is an invisible pit here: heat. When the door of a weak current box is closed, it becomes a stuffy tank. Hot air floats upwards, and whoever is at the top is the hottest. Huawei officials made a rather counter-intuitive statement: the optical modem is installed at an upper position in the box, and hot air accumulates around it. When the box temperature is high, there may be a probability of crash. It is recommended that the optical modem be lowered or the ventilation should be increased. I have actually tested it at home. In summer, with the door closed, the temperature inside the box can reach around 45 degrees, which is very hot to the touch. This temperature is a chronic poison to capacitors. The high temperature of weak current boxes is one of the three major killers of routers. I have written about this specifically ( Router lifespan article (discussed in it).
Therefore, there are two things to remember when setting up the cabinet: put the hot ones at the bottom, leave gaps between the equipment, and don’t stack them; try to replace the door with a louver door, or open a few heat dissipation holes yourself, which only costs a few dollars for an electric drill. There is another old question: Should a weak current box be inserted into the router? My answer is to try not to. The signal is cut in half as soon as the metal box door is closed. The weak current box is at the bottom among the several positions I measured ( Router placement test ). There are only optical modems, switches and power strips left in the box, which is much cleaner - if the network port is not enough and you want to add a switch, I have also written about how to choose and connect it ( Home switch article ).
The power supply is the hardest hit area: the adapters squeeze each other and the plugs and strips cannot fit together.
After sorting out the cables, you will find that the thing that takes up the most space in the weak current box is not the network cable, but several large power adapters, each occupying two holes. A few simple methods: First, change to a small size adapter. Check the power specifications of the optical modem and switch clearly before buying. The voltage must be exact, and the current should only be large or small. You can buy narrow strips online for more than a dozen yuan. Just label the corresponding device name on the adapter, otherwise Two black plugs that look the same will be indistinguishable after half a year; secondly, they use staggered plug strips with large hole spacing, so the adapters do not fight with each other; thirdly, they are really crowded, so they use cable ties to hang the adapters on the wall of the box, leaving only the plugs in the strips, and a large area of the box is immediately freed up.
Don't be cheap on the plug strip itself. The box is full of things that are powered 24 hours a day. I don't dare to use the one-to-three converter that costs 99 yuan. If you have a NAS at home, the optical modem switch in the weak current box is also worth connecting to a small UPS. The few minutes during the power outage are enough for the equipment to support the handshake again. I have calculated this ( The article about NAS equipped with UPS ). If you don't have a NAS, you don't have to worry about it. You can replace the plug strip with one with a main switch and cut off the power when you are traveling far away - but if you think about whether you want to watch IPTV on the day you get home, it will take a while for the box to power off and restart.
Three rules for cable management: leave a loop on the fiber coil, leave a margin on the network cable, and separate the strong and weak sides.
The lines are identified, the equipment is laid out, and the finishing touches are fixed. Three rules, all of which I have tripped over:
One is the large circle of fiber optic disks. The radius should be at least 5 centimeters, and should be coiled along the wall of the box. The ties should be loosely fixed and do not make any blind bends. The light attenuation of optical fiber increases as soon as it is refracted, and even if the network speed drops by half, it is considered light.
Second, leave margin at both ends of the network cable. Leave 15 to 20 centimeters on each end, roll it into a small circle and fix it with the edge. The crystal head and panel module are both wearing parts. How can I press a head again (I have written a tutorial on how to press it). Crystal head article ), you can use it if you have any leftover, but if you don’t have any leftover, you have to run the cable through the wall again, and it’s too late to cry. The one in my study was originally cut too bald. Later, the panel broke and I had to use open stitching to repair it. It was terribly ugly.
Third, don’t bundle network cables and power cables. It’s not that the interference is scary, I basically don’t feel the interference at 100Mbps or 100Mbps. The main reason is that the power supply is thick and hot, and the network cables are bundled together and suffer, and they cannot be disassembled for subsequent maintenance. Partitioning: The power supply is on one side, and the network cable is on the other side. The distinction is clear. Don't strangle the tie, leaving a finger gap for easy replacement later.
Finished: Both ends have the same standard, and the wiring diagram is stored in the mobile phone.
Labels are the only serious part of this decluttering worth spending money on. The rule is that both ends have the same label: "Study-2" is affixed on the end of the box, and "Study-2" is affixed on the other end of the study panel, with the same number. Posting only one end means not posting it at all. Half a year later, you won’t even be able to remember which room “No. 2” is. Use waterproof label paper, or textured paper with a marker. Do not use your mouth to pick up the paper. The weak current box will get damp and the edges will warp and fade quickly.
Before finishing the work, take photos of the finished boxes again, along with the whereabouts of each wire, and save them in the photo album of your mobile phone to create a collection of "weak current boxes". This picture is the network map of your home. In the future, if something breaks down, you need to add new equipment, or call the master to come to your home, you can easily understand it at a glance by taking out your mobile phone, which will save the trouble for the master.
| What's going on with your family? | How to fix it |
|---|---|
| There are no labels on the network cables, so I can’t tell which cable is which. | The two of them work together to pull out the roots one by one and try to label them, or they can spend dozens of yuan to buy a line finder. |
| The adapters squeeze each other and the plug strips are not fully plugged in. | Replace with narrow adapters, staggered hole spacing plugs, or cable ties to hang on the box wall |
| The temperature inside the box is high and the equipment is hot to the touch | Put the optical modem in a low position, don't stack the arhat, replace the shutter door or open a heat dissipation hole |
| Do not dare to touch optical fiber | The radius of the large circle is 5 cm, and the tie is loose and fixed, and do not break any dead corners. |
| It's being renovated, everything can be done again | Stop sorting it out and just look at it Decoration wiring planning , change to a large box in one step |
The entire process is arranged in order: taking photos and archiving, identifying and labeling the cables, rearranging the equipment, sorting the power supply, organizing and fixing the cables, and then taking a final photo and storing it in the mobile phone. One afternoon is enough, and in exchange, I won’t have a headache every time I unpack it. Cleaning up weak current boxes can last for many years at a time, and it is worth picking a weekend to do it seriously.
